Microprocessors Questions and Answers – Design of a PC Based Multimicroprocessor System

This set of Microprocessor Multiple Choice Questions & Answers (MCQs) focuses on “Design of a PC Based Multimicroprocessor System”.

1. The files that reside in the current drive and directory of the hard disk is
a) OBJ files
b) EXE files
c) SRC files
d) DEST files
View Answer

Answer: b
Explanation: The files that reside in the current drive and directory of the hard disk is EXE files.

2. The master processor stores the result buffers on to the hard disk with the filename as
a) .EXE file
b) .OBJ file
c) .EXE file with extension .RES
d) .OBJ file with extension .RES
View Answer

Answer: c
Explanation: The master processor stores the result buffers on to the hard disk with the filename as .EXE file with extension .RES.

3. The 8288 bus controller chip derives the signals
a) ALE
b) DEN
c) DT/R(active low)
d) All of the mentioned
View Answer

Answer: d
Explanation: The latches are enabled by ALE signal and data will be enabled by DEN signal. The ALE, DEN and DT/R(active low) signals are derived by a separate 8288 bus controller chip.
advertisement
advertisement

4. The EXE files should not exceed the size of
a) 30 KB
b) 50 KB
c) 60 KB
d) 40 KB
View Answer

Answer: c
Explanation: The EXE files should not be more than 60 KB size.

5. A part of memory that can be addressed by more than one processor for communication is known as
a) memory module
b) bus window
c) ram
d) memory management unit
View Answer

Answer: b
Explanation: There are two slave processors and thus there are two bus windows.
Sanfoundry Certification Contest of the Month is Live. 100+ Subjects. Participate Now!

6. When a subprocessor wants to communicate with the bus window, it informs the main processor to
a) enable control buffer
b) storage buffer
c) disable tristate buffer
d) translation look aside buffer
View Answer

Answer: c
Explanation: An 8255 IO card is used to control the tristate buffers that provide isolation. When a subprocessor wants to communicate with the bus window, it informs the main processor to disable tristate buffer.

7. When the subprocessor completes its execution, then the status on the status lines shows
a) hold status
b) halt status
c) high status
d) low status
View Answer

Answer: b
Explanation: When the subprocessor completes its execution, then the status on the status lines shows halt status.
advertisement

8. For MEMR(active low) and MEMWR(active low) operations the mode of isolation buffer should respectively be in
a) receiver mode, receiver mode
b) transmit mode, receiver mode
c) receiver mode, transmit mode
d) transmit mode, transmit mode
View Answer

Answer: c
Explanation: During MEMR(active low) the data flow from memory to CPU so isolation buffer should be in receiver mode and data flows from CPU to memory during MEMWR(active low) operation and so buffer should be in transmit mode.

9. If the DIR pin of the isolation chip is high, then it enters into
a) receiver mode
b) virtual access mode
c) transmit or receive mode
d) transmit mode
View Answer

Answer: d
Explanation: If the DIR pin of the isolation chip is high, then it enters into transmit mode and if it is 0 then the isolation chip enters into receiver mode.
advertisement

10. The complete software system is divided into
a) main program
b) Interrupt routine IRT2 for first subprocessing the unit
c) Interrupt routine IRT3 for first subprocessing the unit
d) all of the mentioned
View Answer

Answer: d
Explanation: System software of the complete system consists of three parts. the first part main control program controls the total operation of the system, and the remaining two parts are the small local initialization programs for each of the subprocessors.

Sanfoundry Global Education & Learning Series – Microprocessors.

Here’s the list of Best Books in Microprocessors.

To practice all areas of Microprocessors, here is complete set of 1000+ Multiple Choice Questions and Answers.

If you find a mistake in question / option / answer, kindly take a screenshot and email to [email protected]

advertisement
advertisement
Subscribe to our Newsletters (Subject-wise). Participate in the Sanfoundry Certification contest to get free Certificate of Merit. Join our social networks below and stay updated with latest contests, videos, internships and jobs!

Youtube | Telegram | LinkedIn | Instagram | Facebook | Twitter | Pinterest
Manish Bhojasia - Founder & CTO at Sanfoundry
Manish Bhojasia, a technology veteran with 20+ years @ Cisco & Wipro, is Founder and CTO at Sanfoundry. He lives in Bangalore, and focuses on development of Linux Kernel, SAN Technologies, Advanced C, Data Structures & Alogrithms. Stay connected with him at LinkedIn.

Subscribe to his free Masterclasses at Youtube & discussions at Telegram SanfoundryClasses.