Instrumentation Transducers Questions and Answers – Displacement to Pressure Transducers

This set of Instrumentation Transducers Questions and Answers for Experienced people focuses on “Displacement to Pressure Transducers”.

1. Which of the following uses displacement to pressure conversion?
a) Flapper nozzle system
b) Gyroscope
c) Viscometer
d) None of the mentioned
View Answer

Answer: a
Explanation: Flapper nozzle system is an example of displacement to pressure conversion system, in which displacement between flapper and nozzle is proportional to the pressure of outflow.

2. Displacement to pressure systems are used for measuring ___________
a) Displacement
b) Velocity
c) Acceleration
d) Force
View Answer

Answer: a
Explanation: In displacement to pressure conversion system, Pressure corresponding to displacement is measured.

3. Which of the following represents the correct relation between pressure and displacement in flapper nozzle system?
a) Direct proportionality
b) Inverse proportionality
c) Equal
d) None of the mentioned
View Answer

Answer: b
Explanation: In flapper nozzle system, as the displacement between flapper and nozzle increases, pressure decreases.
advertisement
advertisement

4. Which of the following represents normal value for Pout/Pin?
a) Less than 0.2
b) Between 0.2 and 0.75
c) Between 0.75 and 1
d) Greater than 1
View Answer

Answer: c
Explanation: Practically ratio of output pressure and input pressure has a value between 0.2 and 0.75.

5. Which of the following is correct for flapper nozzle system?
a) Used in hydraulic system only
b) Used in pneumatic system only
c) Used in both hydraulic and pneumatic system
d) None of the mentioned
View Answer

Answer: c
Explanation: Flapper nozzle system can be used in both hydraulic and pneumatic systems.
Sanfoundry Certification Contest of the Month is Live. 100+ Subjects. Participate Now!

6. Range of displacement of flapper required to change output pressure over the useful range is known as ___________
a) Cut-off displacement
b) Throttling range
c) Threshold value
d) Break value
View Answer

Answer: b
Explanation: Value of the throttling range should be as low as 0.1mm.

7. Which of the condition is applicable for flapper nozzle system?
a) Measuring air should be free from dust
b) Measuring air must be of constant pressure
c) Measuring air should be of free from dust and of constant pressure
d) None of the mentioned
View Answer

Answer: c
Explanation: For passing air through flapper nozzle system, it should be of constant pressure and free from any dust particles.
advertisement

8. Which of the following represents condition for a volume of chamber?
a) As large as possible
b) Limited to 5 cc
c) AS small as possible
d) No limit
View Answer

Answer: b
Explanation: Volume of the chamber is limited to 5cc for reducing the time constant.

9. Which of the following represents ideal flapper nozzle system?
a) Ratio of output and input pressure 0.75 at displacement = 0
b) Ratio of output and input pressure 1 at displacement = 0
c) Ratio of output and input pressure 0.5 at displacement = 0
d) Ratio of output and input pressure 0 at displacement = 0
View Answer

Answer: b
Explanation: Ideally pressure of inflow and outflow are equal at zero displacement, that is the ratio of output and input pressure will be 1.
advertisement

10. At which point of displacement pressure chara has maximum slope?
a) 0.14(di/dt)2
b) (di/dt)
c) 0.5(di/dt)2
d) None of the mentioned
View Answer

Answer: a
Explanation: At displacement of 0.14(di/dt)2, displacement to pressure characteristic is found to have maximum slope.

Sanfoundry Global Education & Learning Series – Instrumentation Transducers.

To practice all areas of Instrumentation Transducers for Experienced people, here is complete set of 1000+ Multiple Choice Questions and Answers.

If you find a mistake in question / option / answer, kindly take a screenshot and email to [email protected]

advertisement
advertisement
Subscribe to our Newsletters (Subject-wise). Participate in the Sanfoundry Certification contest to get free Certificate of Merit. Join our social networks below and stay updated with latest contests, videos, internships and jobs!

Youtube | Telegram | LinkedIn | Instagram | Facebook | Twitter | Pinterest
Manish Bhojasia - Founder & CTO at Sanfoundry
Manish Bhojasia, a technology veteran with 20+ years @ Cisco & Wipro, is Founder and CTO at Sanfoundry. He lives in Bangalore, and focuses on development of Linux Kernel, SAN Technologies, Advanced C, Data Structures & Alogrithms. Stay connected with him at LinkedIn.

Subscribe to his free Masterclasses at Youtube & discussions at Telegram SanfoundryClasses.