We have compiled the list of Best Reference Books on Metallurgy subject. These books are used by students of top universities, institutes and colleges. Here is the full list of best books on Metallurgy along with reviews.
Kindly note that we have put a lot of effort into researching the best books on Metallurgy subject and came out with a recommended list of best books. The table below contains the Name of these best books, their authors, publishers and an unbiased review of books on “Metallurgy” as well as links to the Amazon website to directly purchase these books. As an Amazon Associate, we earn from qualifying purchases, but this does not impact our reviews, comparisons, and listing of these top books; the table serves as a ready reckoner list of these best books.
List of Metallurgy Books with author’s names, publishers, and an unbiased review as well as links to the Amazon website to directly purchase these books.
- Advanced Physical and Mechanical Metallurgy
- Ceramics and Powder Metallurgy
- Design and Metallurgy of Welded Joints
- Advance Ferrous Extractive Materials and Metallurgy
- Material Science and Metallurgy
- Metallurgical Failure Analysis
- Extraction of Non-Ferrous Metals
- Heat Treatment of Metals
1. Advanced Physical and Mechanical Metallurgy
|1. “Physical Metallurgy and Advanced Materials” by R E Smallman and A H W Ngan
Book Review: This book discusses all the basic concepts related to metallurgy and materials science. This book is the updation of the book named modern physical metallurgy. Every chapter in the book contains questions that allow the readers to apply scientific concepts as well as to stress the important material properties. The different topics in the book are atoms, atomic arrangements, crystal defects, phase equilibrium, material analysis and mechanical properties of materials. The chapters in the book also carry out examination of alloys, ceramics, polymers, composites and nonmaterial.
|2. “Physical Metallurgy for Engineers” by Donald S Clark and Wilbur R Varney
“Physical Metallurgy for Engineers” Book Review: The book deals with the concepts of physical metallurgy. It targets students of undergraduate courses in metallurgy. Design elements of metals and alloys are covered. The reader can also find concepts of the appropriate selection of metals and alloys according to the application required. Various properties of these materials are also discussed enhancing the reader in understanding and hence optimizing the treatment of these metals and alloys.
|3. “Computer Simulation in Physical Metallurgy” by Gianni Jacucci|
| 4. “Physical Metallurgy and Processing of Intermetallic Compounds” by Stoloff Sikka
“Physical Metallurgy and Processing of Intermetallic Compounds” Book Review: The book focuses on physical and mechanical properties of intermetallic alloys. It can be of interest to researchers and scientists of the field. The contents of the book are covered in a total of 16 chapters. The initial sections of the book deal with defects, creep, grain boundary structure and brittle toughening. Further, the book describes physical and mechanical metallurgies of a few alloys. Aluminides, silicides and intermetallics are also covered in this text.
| 5. “Liquid Metal Systems: Material Behavior and Physical Chemistry in Liquid Metal Systems” by H U Borgstedt
“Liquid Metal Systems: Material Behavior and Physical Chemistry in Liquid Metal Systems” Book Review: The main idea of the book is behaviour of liquid metal systems. It is recommended to students of higher level courses and researchers carrying out studies in the field. Fundamentals of physical and chemical properties of liquid metals are discussed. Various aspects of corrosion of metals as well as ceramic materials such as reasons for occurrence and prevention methods are also dealt with. Recent advances in the field of fission reactor techniques are covered.
|6. “Physical Metallurgy” by Hosford|
|7. “Physical Chemistry Of Iron & Steel Manufacture” by Bodsworth C|
|8. “Introduction to Physical Metallurgy” by Avner
“Introduction to Physical Metallurgy” Book Review: The book deals with various concepts of physical metallurgy. It is recommended to students, academicians and researchers. Fundamentals of physical metallurgy are covered. A wide range of theoretical aspects are highlighted. Readers can also find numerous applications of the elucidated concepts in the book.
|9. “Physical Metallurgy” by Peter Haasen
“Physical Metallurgy” Book Review: Concepts of solid state physics as well as chemical thermodynamics are covered in this book. It can be of interest to students and metallurgists alike. Various properties of metallic materials are discussed. Landau theory of martensitic transformation and hardening and plasticity of intermetallics is given special importance. Microstructure and transformation of metallic materials with the help of concepts of physical metallurgy is also covered.
|10. “Mechanical Metallurgy” by G Dieter
Book Review: This is the most popular book of mechanical metallurgy and carries out examination of material behavior under stress and captures its reaction to many hostile environments. The book also covers the concepts of mechanical metallurgy taking into consideration the description of stress and strain through crystalline and defect mechanisms of flow and fracture and also takes into consideration the mechanical property tests and basic networking process. SI units have also been added in the book ans additionally the book also contains many end of chapter questions.
|11. “Mechanical Metallurgy” by Dieter G E
“Mechanical Metallurgy” Book Review: The book takes an in-depth look at the production processes with stress on development of control engineering and automation. It provides detailed analysis of several important manufacturing technologies as a system comprising the three elements: process, production line and product. Some of the chapters present in the book are Basic Principles of Metal Forming, Fundamentals of Press Design, Mechanical Process, Hydraulic Process, Changing Dies, Press Safety and Certification, Coil Lines, Sheet Metal Forming Lines, Shearing Lines etc. The book also addresses the recently developed technologies such as CAD, CAM, CIM, mechatronics and process simulation and their influence on modern industrial processes.
| 12. “Modern Physical Metallurgy” by R E Smallman and A H W Ngan
“Modern Physical Metallurgy” Book Review: This book covers basic principles and techniques of physical metallurgy and microstructure assessment. It provides alloys & metals properties and applications in a very deeper pitch. This book provides good coverage of characterization, crystal structure, and corrosion. Additionally, It also talks about phase transformations and properties of metals/alloys. This book provides good coverage of alloy & metals. This book provides various characterizing techniques for materials like nanoindentation, AFM, and STM. It also includes various real-world examples, case studies, and homework exercises. This book contains an image bank and also a manual of online solutions.
|13. “Physical Metallurgy Principles” by R Abbaschian and R E Reed Hill
Book Review: This book makes the readers well known with the theory of x-ray diffraction, the various experimental methods involved and the applications of it. The book contains a set of principles and methods that deal with X-ray diffraction rather than metallurgy. The book uses Bragg law to describe various concepts and is divided into three parts and they are basics, experimental methods and applications. This book is suitable for beginners.
|14. “Mechanical Metallurgy” by Marc A Meyers|
2. Ceramics and Powder Metallurgy
|1. “Powder Metallurgy: An Overview” by I Jenkins and J V Wood
“Powder Metallurgy: An Overview” Book Review: the book deals with concepts of powder metallurgy. It is recommended to researchers and scientists along with students of upper graduate level courses in the subject. The book is a collaboration of various papers and articles dealing with the recent advances of powder metallurgy technology and its current status.
|2. “Powder Metallurgy Science” by R M German|
| 3. “Powder Metallurgy: An Advanced Technique of Processing Engineering Materials” by B K DATTA
“Powder Metallurgy: An Advanced Technique of Processing Engineering Materials” Book Review: The main idea of the book is principles underlying powder metallurgy. It targets students of undergraduate level courses of various domains and industrial engineers. The book deals with various aspects of raw materials used in powder technology such as selection and processing. Several manufacturing methods of both metallic and non-metallic powders are discussed. Emphasis is laid on the technologies of sintering and compacting. Readers can also find numerous practical examples and practice problems throughout the text.
| 4. “Modelling of Powder Die Compaction” by Peter R Brewin
“Modelling of Powder Die Compaction” Book Review: The focus of the book is on compaction models. It can be referred to by researchers of the field, designers and users of powder compaction. The book aids the readers in testing the compaction models. It provides several case studies thereby highlighting the testing process of compaction models for optimization of efficiency.
| 5. “Injection Molding of Metals and Ceramics” by Randall M German
“Injection Molding of Metals and Ceramics” Book Review: The book deals with the injection molding process of metals and ceramic manufacturing process. It targets working professionals of the field and researchers carrying out studies on the topic. The book talks about a forming technique involving thermoplastic binders to shape complex components with the help of injection molding. Various aspects of injection molding as a manufacturing process such as steps, optimization and engine. The main idea of the book is the solid state chemistry and the underlying principles of powder production. It can be accessed by students and researchers alike. Structure, properties and preparation, and characterization of these industrial products are discussed. Basic statistical methods employed in studying the characteristics of particles are elucidated. Recent technological advances in the field of powder technology manufacturing are also covered.
|6. “Chemistry of Powder Production” by Yasuo Arai|
|7. “Advanced Powder Technology III” by Lucio Salgado|
|8. “Powder Metallurgy : For Automotive, Aluminium Alloys, Hard And Super Hard Materials” by Dr P Ramakrishnan
“Powder Metallurgy : For Automotive, Aluminium Alloys, Hard And Super Hard Materials” Book Review: This book discusses the current status and potential of the rapidly expanding manufacturing technology. Topics such as the challenges facing the powder metallurgy (PM) industry, technological advances for the growth of the global PM industry are dealt with. The book is a valuable source for graduate students, researchers, professionals and technocrats. This book contains 25 articles in the field of powder metallurgy. Section 1 covers powder metallurgy in automotive and related industries. The next section contains detailed explanation of aluminium alloys and composites. The book will be useful for undergraduate as well as postgraduate researchers and students in the field of materials, metallurgy, mechanical, production, and manufacturing engineering. It will also benefit scientists, engineers, and technocrats dealing with powder metallurgy and particulate materials. Some of the important contents of the book are powder metallurgy in automotive industry, compaction techniques with improved efficiency and economy, powder plant management etc. The book provides a practice-oriented approach to the readers by including application based examples with step-by-step procedures. Pictures and diagrams are provided wherever needed so that the overall learning experience becomes a blend of theoretical and practical understanding.
| 9. “Advances in Stainless Steels (Metallurgy and Materials Science)” by Baldev Raj and K Bhanu Kankara Rao
“Advances in Stainless Steels (Metallurgy and Materials Science)” Book Review: This book basically discusses the stainless steel, including processing, component design, properties, fabrication, and it also covers its applications. The topics which are covered in this book are the life cycle of stainless steel, from alloy design and characterization to engineering design, fabrication, mechanical properties, corrosion, quality assurance of components etc. It also discusses component design, modeling and structural integrity, manufacturing technology, property evaluation, alloy development and applications, nondestructive evaluation methods, corrosion and surface modification.
3. Design and Metallurgy of Welded Joints
|1. “Design, Fabrication and Economy of Metal Structures: International Conference Proceedings 2013, Miskolc, Hungary, April 24-26, 2013” by Károly Jármai and József Farkas
“Design, Fabrication and Economy of Metal Structures: International Conference Proceedings 2013, Miskolc, Hungary, April 24-26, 2013 ” Book Review: This book is an important guide for civil and mechanical engineers, architects, researchers, structural designers and fabricators because it covers topic such as Structural optimization, Thin-walled structures, Stability, Fatigue, Frames, Fire, Fabrication, Welding technology, Applications, Steel-concrete composite and Special problems.
|2. “Welded Joint Design” by John Hicks
“Welded Joint Design” Book Review: This book is a reference to design and performance of welded joints mainly in steel. It comprehend the static and fatigue strength of welded joints, the selection of steel grades from the point of view of service and manufacturing requirements, the design of components and structures, the influence of fabrication methods and procedures on design, welding processes , inspection techniques, brittle fracture, fracture mechanics tests and their significance to the designer, quality assurance and fatigue and the performance of joints under tubular structures. It is primarily for engineers and draughtsmen but civil and mechanical engineering students use it for theory and practice of design.
|3. “Design and Analysis of Fatigue Resistant Welded Structures (Woodhead Publishing Series in Welding and Other Joining Technologies)” by Dieter Radaj|
| 4. “Recommendations for Fatigue Design of Welded Joints and Components (IIW Collection)” by A Hobbacher
“Recommendations for Fatigue Design of Welded Joints and Components” Book Review: This is a foundation for design and analysis of welded components that are subjected to fluctuating forces, to avoid failure by fatigue and useful for boards or commissions who are establishing fatigue design codes. The aim of designing structures taking note of the limit state for fatigue damage is to ensure that the performance is satisfactory during the design life and that the survival probability is acceptable and this is attained by appropriate use of partial safety factors. The reader can get the most advantage of the book when they have a working knowledge of the basics of fatigue and fracture mechanics.
| 5. “Lifetime Estimation of Welded Joints” by Tadeusz Lagoda
“Lifetime Estimation of Welded Joints” Book Review: The book evaluates the fatigue life of chosen welded joints. It contains topics like problems that accompany deter-nation of the fatigue life of welded joints, welded joint as a stress concentrator, state of stress and strain in the notch, theoretical and fatigue coefficients, fatigue coef-cient of the notch effect, fatigue life assessment under uniaxial stress state with statistical handling of data presented, new energy model of fatigue life assessment, analysis of stress and strain in the critical plane, analysis of tests of four ma-rials subjected to different loadings: cyclic, variable-amplitude with Ga-sian distribution, and variable amplitude with Gaussian distribution and overloading for symmetric and pulsating loading and application of the model in the fatigue life assessment in the complex state of loading.
| 6. “Fatigue Strength of Welded Structures (Design Memoranda)” by K G Richards
“Fatigue Strength of Welded Structures” Book Review: The book includes conditions for fatigue, detail design, nature of the stress variation, corrosion fatigue, high tensile steels, possible improvements in fatigue strength, effect of defects on fatigue strength, typical service failures, and design data.
| 7. “Fatigue Strength of Welded Structures (Woodhead Publishing Series in Welding and Other Joining Technologies)” by S J Maddox
“Fatigue Strength of Welded Structures” Book Review: This book focuses on the need for a design approach that incorporates an understanding of the fatigue problem and effects of welding, the design of welded joints in components or structures and application of fracture mechanics to fatigue. This edition is redrafted to address technological advancement providing practical approach with the latest design rule.
|8. “Thermo-Mechanical Processing of Metallic Materials” by B Verlinden
“Thermo-Mechanical Processing of Metallic Materials” Book Review: The book deals with the underlying principles of thermo-mechanical processing. It can be accessed by graduate students along with working engineers of the field. The contents of the book are covered in three sections. The initial section of the book talks about microstructural science of metallic materials and hence the derived properties. Further, the book discussed recent advances and the present status of technology involved in plastic forming of metals. The last section of the book correlates the former sections with the help of numerous case studies and also provides the scope of TMP processing.
4. Advance Ferrous Extractive Materials and Metallurgy
|1. “Advanced Distillation Technologies: Design, Control and Applications” by Anton A Kiss
“Advanced Distillation Technologies: Design, Control and Applications” Book Review: The main aim of this book is to provide information regarding distillation technology. It also discusses the principles of design, control and seizing of distillation. It also covers the applications of dividing wall columns. The topics which are covered in this book are heat pump, cyclic distillation technology and reactive distillation. It contains the large number of examples and practical implementation of distillation technology.
|2. “Non-ferrous Extractive Metallurgy – Industrial Practices” by Roger Rumbu
“Non-ferrous Extractive Metallurgy – Industrial Practices” Book Review: This book is basically designed for metallurgists, chemists, and students of mine engineers. The main aim of this book is to provide information about metals. This book contains the flow-sheets, sketches and graphs which helps the readers in understanding the concepts. It also discusses the metal extraction process in an advanced manner.
|3. “Advanced Materials (European Centres of Expertise)” by Enrico Pigorsch
“Advanced Materials (European Centres of Expertise)” Book Review: It is designed for the engineering students, researchers and those who are interested in this field. This book provides the information of european organisations developing advanced materials. Many types of metals are discussed in this book. Some of them are ferrous metals, non-ferrous metals, alloys, oxides, carbides, nitrides and thermoplastics. And it also provides the applications of metals in various fields like aerospace, defence, electrons and optical.
| 4. “Advanced Processing of Metals and Materials (Sohn International Symposium): Non–ferrous Materials Extraction and Processing New, Improved and Existing Technologies” by Florian Kongoli and Ramana G Reddy
“Advanced Processing of Metals and Materials (Sohn International Symposium): Non–ferrous Materials Extraction and Processing New, Improved and Existing Technologies” Book Review: It discusses the nonferrous high temperature, materials processing, ceramic and composite materials processing. The topics which are covered in this book are plenary, aqueous processing, preparation and synthesis. The main aim of this book is to provide the information of metals and materials. It also covers the information of extraction technology. This book gives information regarding non-ferrous materials extraction and processing also. And explains nonferrous high temperature processing. It deals with topics materials processing; and nano, ceramic and composite materials processing.
| 5. “Part 2: Non-ferrous Alloys – Light Metals: Subvolume C: Metal Forming Data – Volume 2” by Thilo Spittel and Marlene Spittel
“Part 2: Non-ferrous Alloys – Light Metals: Subvolume C: Metal Forming Data – Volume 2” Book Review: It is designed for the students of metallurgy, researchers and scientists. This book deals with the forming data of metals. It is divided into three parts. It also discusses the non-ferrous light metals. It focuses on physical and mechanical properties of materials. It also explains the curves like plasticity curves and flow curves. The deformation behaviour of materials is also covered in this book.
| 6. “Characterization of Minerals, Metals, and Materials 2013” by Chengguang Bai and Jiann–Yang Hwang
“Characterization of Minerals, Metals, and Materials 2013” Book Review: This book summarizes nickel and cobalt features in industry. This book focuses on the minerals, metals, and materials. The topics which are discussed in this book are clays, ceramics, composites, ferrous metals and non-ferrous metals. It covers the theories of material science. It also focuses on electronic materials, magnetic materials, environmental materials. This also covers the materials extraction, materials processing, corrosion, welding, solidification. It talks about ore supplies and processing. It also deals with ore applications development, and recycling. This book contains a collection of authoritative papers. It also contains nickel and cobalt processing. This book describes fundamentals, technology, operating practices. It explains Platinum-Group Metals (PGM). It even summarizes treatment of sulphide. This book even contains laterite ores, concentrates, and secondary materials for the production of nickel and cobalt.
| 7. “Fatigue of Materials III: Advances and Emergences in Understanding” by M Ashraf Imam and T S Srivatsan
“Fatigue of Materials III: Advances and Emergences in Understanding” Book Review: This book is designed for the engineers, scientists and technologists. It is divided into five parts. It covers the topics like aluminium alloys, composite materials, ferrous materials, models and advanced materials. It also focuses on the behaviour of aluminium alloy composite. The role of plasticity is also discussed.
| 8. “The Extractive Metallurgy of Gold” by John C Yannopoulos
“The Extractive Metallurgy of Gold” Book Review: This book focuses on the extraction of gold from its ores. It covers the extractive metallurgy courses. It is designed for engineering students, scientists and technologists. It basically focuses on the extraction of gold. The topics which are covered in this book are physical/chemical properties of gold and treatment of placer deposits. This book also explains the process of refining.
| 9. “Principles of Extractive Metallurgy” by Ahindra Ghosh and Hem Shanker Ray
“Principles of Extractive Metallurgy” Book Review: It is designed for the undergraduate and postgraduate students of chemical engineering, metallurgy engineering. The topics which are covered in this book are thermodynamic aspects and transport phenomena. It also contains the summaries of metallurgical units. This book also explains the extraction, reactor analysis, fluid flow, and pseudo steady diffusion.
| 10. “Extractive Metallurgy 1: Basic Thermodynamics and Kinetics” by Alain Vignes
“Extractive Metallurgy 1: Basic Thermodynamics and Kinetics” Book Review: This book is designed for the students of metallurgy engineering, chemical engineering and mechanical engineering. The topics which are covered in this book are heat & matter assessment, process coupling, chemical reactions and transport phenomena. It covers the processes of mineral transformation, recycling and reclamation of metals. It also explains the physico-chemical bases of transformations.
|11. “Electronic Waste: Recycling Techniques (Topics in Mining, Metallurgy and Materials Engineering)” by Hugo Marcelo Veit and Andréa Moura Bernardes
“Electronic Waste: Recycling Techniques (Topics in Mining, Metallurgy and Materials Engineering)” Book Review: This book presents an overview of the characterization of electronic waste. It also focuses on the recycling techniques of the electronic waste by including various relevant topics in mining, metallurgy and materials engineering. In addition, processing techniques for the recovery of metals, polymers and ceramics are described. The topics are discussed with the help of real-world case studies and examples that provide a practical understanding of the subject. This book serves as a source of information and as an educational technical reference for practicing scientists and engineers, as well as for students.
|12. “Metallurgy and Design of Alloys with Hierarchical Microstructures” by Krishnan K Sankaran and Rajiv S Mishra
“Metallurgy and Design of Alloys with Hierarchical Microstructures” Book Review: This book is written for the postgraduates of metallurgical engineering. It can also be used as a reference by academic researchers and practicing engineers. The book covers the topics of metallic materials used in aircraft structures. It covers the topics of microstructural complexity of structural materials. It integrates the concepts of computational materials science, physical metallurgy and alloy design. It focuses on deformation mechanisms, durability and damage tolerance in different materials. The book has many real-life examples. It discusses in detail the science behind the efficient design of materials.
5. Material Science and Metallurgy
|1. “Physical Metallurgy, Principles and Practices” by V Raghavan
“Physical Metallurgy, Principles and Practices” Book Review: The book discusses the principles and applications of engineering metals and alloys. The coverage of the book includes phase diagrams, phase transformations, heat treatment of steels and nonferrous alloys, solidification, fatigue, fracture and corrosion etc. It also addresses Thermoelastic martensite; Shape memory alloys; Rapid solidification processing; and, Quaternary phase diagrams etc. The text is provided in clear and readable format, making it easy to understand. Figures and diagrams have been added in abundance for better comprehension. The book can benefit students in Metallurgy/Metallurgical and Materials Engineering as well as professionals.
|2. “Material Science and Metallurgy” by O P Khanna|
| 3. “Material Science and Metallurgy” by Jindal
“Material Science and Metallurgy” Book Review: The textbook provides discussions and explanations on the basic concepts of the structure of various materials and various physical, structural and electrical properties of these materials. The coverage of the book includes Diffusion, Phase Diagrams, Phase Transformations, Composite Materials, Wear of Materials, Corrosion and Oxidation, Thermal Properties, Electrical Conductivity and Insulating Properties, Semiconductors, Dielectric Properties, Magnetic Properties, Heat Treatment of Steels, Metals and Alloys, Organic Materials, Ceramic Materials etc. The book is supplemented with multiple choice questions, solved problems, review questions as well as diagrams and figures for better understanding and extensive practice.
|4. “Material Science and Metallurgy” by K I Parashivamurthy|
| 5. “Material Science and Metallurgy for Engineers” by Dr V D Kodgire
“Material Science and Metallurgy for Engineers” Book Review: The textbook discusses the structure and properties of various materials and the underlying science surrounding these materials. It is organized into a total of seventeen chapters. The book can benefit undergraduate students in metallurgy engineering or material science and related fields. It not only provides essential understanding of the topics but can also be used in preparation for university examinations. The coverage of the book includes Structure of Materials, Plastic Deformation, Mechanical Testing and Evaluation of Properties, Non-destructive Testing, Equilibrium Diagrams, Corrosion and Prevention, Temperature Measurement (Pyrometry), Metallography (Optical and Electron), Steels and Heat Treatments, Engineering Alloy Steel, Cast Irons, Engineering Non-Ferrous Alloys, Strengthening Mechanisms, Powder Metallurgy, Polymers, Joining Processes and Methods of Surface Improvement.
|6. “Engineering Materials & Metallurgy” by R K Rajput
“Engineering Materials & Metallurgy” Book Review: The textbook covers structure and structural properties of various materials and concepts on metallurgy. The coverage of the book includes Alloys, Phase Diagrams, Heat Treatment, Ferrous (and Non-Ferrous) Metals, Non-Metallic Materials and Mechanical Properties and Testing etc. It also covers basic concepts and background knowledge such as Structure of Atoms and Molecules, Miller Indices, Imperfections (Defects) in Crystals and Grain Size Determination. Some of the chapters present in the book include Constitution of Alloys and Phase Diagrams, Heat Treatment, Ferrous and Non-Ferrous Metals, Non-Metallic Materials, Mechanical Properties and Testing. The book is supplemented with short and long answer type questions as well as an abundant number of tables, figures, examples and MCQs to aid learning.
| 7. “MATERIAL SCIENCE AND METALLURGY” by GATE ACADEMY TEAM
“Material Science and Metallurgy” Book Review: The textbook focuses on the study of material science and metallurgy, primarily for the preparation of GATE exam. The content of the book includes chapters and topics according to the gate syllabus. The topics have been covered in a systematic and coherent manner with apt explanations and discussions. Abundant number of questions are provided for practice including questions from previous year GATE question papers. The book can help students understand the concepts and prepare for various competitive examinations.
6. Metallurgical Failure Analysis
|1. “Analysis of Metallurgical Failures” by Vito J Colangelo and Francis A Heiser
“Analysis of Metallurgical Failures, 2nd Edition 2nd Edition” Book Review: This is designed for undergraduate students. It helps understand to determine the validity of products by analysing metallurgical failures. The book highlights the new features in electron microscopy. Fracture techniques and mechanisms have also been explained. Destructive and non-destructive techniques along with its applications, advantages and much more is contained in this book. The problems are addressed from both a physical and mechanical viewpoint.
|2. “Analysis of Metallurgical Failures” by COLANGELO|
|3. “Metallurgical Failure Analysis” by Charlie R Brooks and Ashok Choudhury
“Metallurgical Failure Analysis 1St Edition” Book Review: This book is designed for those involved in the design, installation, or operation of machines or structural components. The book provides the best techniques to identify the causes of failure in metal parts.
| 4. “Metallurgical Science for Failure Analysis and Nde Engineers (Including Descriptive Thermodynamics)” by J W Bell
“Metallurgical Science for Failure Analysis and NDE Engineers (Including Descriptive Thermodynamics)” Book Review: This book is designed to be used for undergraduate students of metallurgy as a one semester text. The principles governing metallurgy are given in simple language along with a number of examples. The book begins with reviewing the key concepts. The following sections cover the three primary metallic crystals and electrochemical corrosion. The book details thermodynamics. With a no. of formulas, it assumes basic knowledge of algebra.
| 5. “Metallurgical Failure Analysis: Techniques and Case Studies” by Kannadi Palankeezhe Balan
“Metallurgical Failure Analysis: Techniques and Case Studies 1st Edition” Book Review: this book is designed for scientists, metallurgists, engineers, quality control inspectors, professors and students. The book analyses the causes and the ways to avoid failures. The fundamentals of failure analysis is covered in this book. The book examines 37 case studies for the purpose of illustrations. Case studies are also organised depending on the various causes of failure for better understanding. Case studies range from improper material selection, manufacturing defects etc.
| 6. “Investigating Mechanical Failures: The metallurgist’s approach” by R B Ross
“Investigating Mechanical Failures: The metallurgist’s approach 1995th Edition” Book Review: The book talks about mechanical failures. The book contains information about how to clearly and in an understandable language.
| 7. “Metallurgy Fundamentals: Ferrous and Nonferrous” by Daniel A Brandt and J C Warner
“Metallurgy Fundamentals: Ferrous and Nonferrous” Book Review: This book provides students with the fundamentals of metallurgy. The text is presented in an easy and clear language. A no. of illustrations have also been presented for better understandable. Over 450 tables and examples are also included in this text.
|8. “ASM Metals Failure Analysis and Prevention” by W T Becker
“ASM Metals Failure Analysis and Prevention” Book Review: This book focuses on the root causes of failure, describes the principles, practices, and analytical techniques of failure analysis, so that root causes are properly identified and corrected for the ultimate objective of failure prevention. It begins with the general aspects of failure prevention from the fundamentals and also investigates them thoroughly to establish a good foundation for the reader. It is an effective handbook for manufacturing engineers, component designers, a materials failure analyst, or someone with a general interest in the nature and prevention of engineering failures.
7. Extraction of Non-Ferrous Metals
|1. “Extraction Of Nonferrous Metals” by H S and Ray|
|2. “Extraction of Nuclear and Non-ferrous Metals (Topics in Mining, Metallurgy and Materials Engineering)” by Sujay Kumar Dutta and Dharmesh R Lodhari
“Extraction of Nuclear and Non-ferrous Metals (Topics in Mining, Metallurgy and Materials Engineering)” Book Review: This book deals with non-ferrous metallurgy. It contains core principles and fundamental aspects. This book provides basic concepts and definitions related to metal extraction. It also summarizes metallurgical processes. It provides scientific and engineering aspects of nuclear processes. This book also describes ultra-high-purity metals. This book is understandable and easy to read. It also gives details about core concepts. This book interests professionals and researchers. This book contains metallurgy, mining, and chemical engineering. This book is for graduate and professional coursework.
|3. “Non-Ferrous Foundry Metallurgy: The Science of Melting and Casting Non-Ferrous Metals and Alloys” by Alfred John Murphy|
| 4. “Extractive Metallurgy of Non-ferrous Metals” by Dr R Raghavan
“Extractive Metallurgy of Non-ferrous Metals” Book Review: This book mainly deals with Extractive Metallurgy of Non-ferrous Metals. It explains about the non-ferrous metallurgical industry. It describes the passion for developing innovative extractive metallurgical processes. This book is very understandable. It also explains extractive metallurgical processes in the area of non-ferrous metals.
| 5. “The Complete Book on Ferrous, Non-Ferrous Metals with Casting and Forging Technology” by NIIR Board of Consultants and Engineers
“The Complete Book on Ferrous, Non-Ferrous Metals with Casting and Forging Technology” Book Review: This book summarizes Casting and Forging. It also gives construction (building and non-building) and automotive sectors. It briefly explained Ferrous and non ferrous metals and its alloys. It also explains Metal ingots and billets. It also gives us the metal casting process, selection of right alloy, size. It also contains shape, thickness, tolerance, texture, and weight. This book explains the Forging technology. It helps us understand the use of machinery with a hammering or pressing action. This book explains production of ferrous and non ferrous metals. This book is useful for industries, technocrats, technical institutions.
|6. “A List of Alloys Prepared by William Campbell for Committee B-2 on Non-Ferrous Metals and Alloys” by American Society for Testing Materials
“A List of Alloys Prepared by William Campbell for Committee B-2 on Non-Ferrous Metals and Alloys” Book Review: This book deals with Non-Ferrous Metals and Alloys. It explains nomenclature of non ferrous metals and alloys. It also gives us a logical and scientific classification of alloys. It also gives us an alloy of copper with zinc. It gives principal alloying metal. It also talks aboutTobin bronze, manganese bronze. It also describes a few examples for iron alloys (in contra-distinction to steel). It explains non-corrosive alloys and of the heat-resisting alloys.
| 7. “The Metallurgy Of The Non-Ferrous Metals” by William Gowland
“The Metallurgy Of The Non-Ferrous Metals” Book Review: This book summarizes metallurgy of metals. This also focuses on non-ferrous metals. It also contains antique metallurgic literature. This book explains Definition of Refractory Materials’, ‘General Uses and Classification. It also deals with Acid Refractory Materials’, ‘Fire-Clays’. It even explains Fire-Bricks’, ‘Agalmatolite’, ‘Neutral Refractory Materials’, ‘Basic Refractory Materials. Ut helps us understand Crucibles’, ‘Classification of Processes’, ‘Heap Roasting’, ‘Roasting of Ores in Lumps. This book is an affordable edition.
|8. “Modern Technology Of Non-ferrous Metals And Metal Extraction” by Eiri Board
“Modern Technology Of Non-ferrous Metals And Metal Extraction” Book Review: This book summarizes Non Ferrous metals and Materials. It deals with processing of copper from Its ore. It also helps us understand Lead and Zinc Recycling. This book describes Chromium Wastes and Their Recycling for the Reclamation of Chromium. It gives us Electrodeposition of cobalt from Cobalt chloride N-(N-Butyl) Pyridinium Chloride Molten Salt. It explains Pyrohydrolysis. It also explains processing of Low Grade Tungsten Ore. It briefs extraction of Copper. It gives us nickel and Cobalt, Extraction of Nickel. It deals with Production of Uranium Metal. It describes Alumina-Aluminium Processing. This book describes drawing of Copper and Aluminium conductors. This book is helpful for Process for the Enrichment of Nickel. It is also helpful for Processing of Lead Zinc Raw Materials. It also explains Extraction of Copper by Di-(2- Ethylhexyl) Dithiophosphate Salts. This book deals with Solvent Extraction in the Processing of Leach and Waste Solutions.
8. Heat Treatment of Metals
|1. “Heat Treatment of Metals” by B Zakharov
“Heat Treatment of Metals” Book Review: The book provides elaborate discussions on heat treatment of metals. The coverage of the book includes Transformations in Steel during its Heat-Treatment, Elements of the Process of Heat-Treating, Heat-Treating Processes, and Heat-Treatment of Cast Irons and Non-Ferrous Alloys, transformations in steel during its heat, transformations in Steel on heating, Transformations in Steel on Cooling etc. The book can benefit undergraduate as well as postgraduate students in mechanical engineering and related fields.
|2. “Physical Metallurgy for Engineers” by Donald S. Clark
“Physical Metallurgy for Engineers” Book Review: The book deals with the field of physical metallurgy. The coverage of the book includes selection, treatment, and use of metals and alloys, the structure of matter, physical properties, and mechanical properties, metallurgy in engineering, metals and alloy systems, iron carbon alloys etc. The emphasis is given to the fundamentals and caters to the understanding of the basic science and art of metallurgy. The book can be of use to all those who want to brush up their basics and get good hold of the fundamental principles.
|3. “Heat Treatment of Metals” by Vijendra Singh
“Heat Treatment of Metals” Book Review: The book provides elaborate discussions on heat treatment of metal. The coverage of the book includes iron-carbon diagram, grain size of steels, Hardenability, heat treatment of steels, heat treatments to ferrous and non-ferrous metals and alloys, hardening due to age, Indian standards, AISI specifications and British standards etc. The book also provides clear demonstrations on software metallurgies in formulating computer programmes particularly in selection of steel for a new product or for replacement of costly steel. It also provides numerous numerical problems that can provide readers with practical exposure to steel design. The book can benefit not only students in metallurgy engineering but also engineers working in the industry.
| 4. “Heat Treatment: Principles and Techniques” by Rajan
“Heat Treatment: Principles and Techniques” Book Review: The book elaborates on heat treatment and its applications in achieving the designed characteristics in a given material. The book provides a comprehensive coverage of various important concepts such as heat treatment of commercial steels, cast irons and non-ferrous metals and alloys, nature of metals and alloys; principles of heat treatment of steels; heat treatment processes; possible defects, causes and remedies in heat treatment; and inspection and quality control in heat treatment. The book is packed with a number of figures for better understanding and an exhaustive set of problems and multiple choice questions for extensive practice.
| 5. “Heat Treatment of Metals, Vol.1” by J L Smith and G M Russell
“Heat Treatment of Metals, Vol.1” Book Review: This textbook is available in two volumes and together, these volumes provide a comprehensive understanding of steel heat treatment with a practical approach. The coverage of this volume includes residual stress and distortion, hardenability, prediction, modeling, effects of steel alloy chemistry on heat treatment, vacuum heat treatment, quenching, process equipment carburizing, nitriding, and metallography. The book also elaborates on materials, manufacturing, heat treatment, maintenance, mechanical, industrial, and process and quality control aspects of heat treatment. The book can serve as a ready reference for undergraduate and graduate students in relevant disciplines.
| 6. “Heat Treatment of Metals, Vol.2” by J L Smith and G M Russell
“Heat Treatment of Metals, Vol.2” Book Review: The book, available in two volumes, provides a complete understanding of heat treatment of metals. The coverage of this textbook includes topics such as treatments for tool steels, stainless steels, and powder metallurgy components, vacuum processes, designing quench processes, steel transformation mechanisms, nitriding techniques, metallurgical property testing, and distortion of heat-treated components etc. The book provides updated coverage on various industrial trends, nomenclature and classifications. The book can serve as a guide for students as well as practitioners in metallurgy engineering and relevant fields.
| 7. “Steel Heat Treatment Handbook (Steel Heat Treatment Handbook, Second Edition)” by George E Totten and Maurice A H Howes
“Steel Heat Treatment Handbook (Steel Heat Treatment Handbook, Second Edition)” Book Review: This textbook provides a comprehensive coverage of steel heat treatment. The coverage of the book includes residual stress and distortion, hardenability prediction, modeling, effects of steel alloy chemistry on heat treatment, quenching, carburizing, nitriding, vacuum heat treatment, metallography, and process equipment. It also covers principles of heat treatment, quenching technology, strain gauge procedures, X-ray diffraction, and other residual stress measurement methods. It makes use of an uncountable number of tables, figures and photographs for fine delivery of theory and understandability.
| 8. “Casting, Heat Treatment and Metal Joining Process: Manufacturing Engineering” by SAURABH KUMAR
“Casting, Heat Treatment and Metal Joining Process: Manufacturing Engineering” Book Review: The book provides a practical take on the various aspects of manufacturing such as casting, heat treatment and metal joining processes. The coverage of the book includes casting process, pattern allowance, slush casting, die casting, shell casting, Annealing, normalizing, hardening, metal joining process etc. The text is presented in an interactive manner. The book also provides explanations on types of welding, grafting system, tempering etc. It covers each concept in a question-answer format. The theory is supported by diagrams, figures and colored photographs.
| 9. “Heat Treatment, Selection and Application of Tool Steels” by William E Bryson
“Heat Treatment, Selection and Application of Tool Steels” Book Review: The book deals with heat treatment, selection and applications as well as practical information about machinability, shock resistance, wear, and extending tool life. The coverage of the book includes properly heat treating a wide range of tool steels, powdered tool steel CPM 10V, carburizing, cryogenic treatment etc. The book makes use of a comprehensive glossary and tables on properties, attributes, qualities etc. The book can be of great use to students in metallurgy engineering and related fields. It can also cater to the needs of tool makers, heat treaters, and engineers working in the industry.
| 10. “PHYSICAL METALLURGY: PRINCIPLES AND PRACTICE” by V RAGHAVAN
“Physical Metallurgy: Principles and Practice” Book Review: The book provides discussions on principles and applications of engineering metals and alloys. The coverage of the book includes phase transformations, heat treatment of steels and nonferrous alloys, shape memory alloys, solidification, fatigue, fracture and corrosion, application of engineering alloys, nanomaterials etc. It also provides thorough coverage of phase diagrams and various other concepts of physical metallurgy. The book can benefit students in metallurgy engineering and other relevant fields. The book can also be a useful resource in preparing for various competitive examinations.
People who are searching for Free downloads of books and free pdf copies of these books on Metallurgy – we would like to mention that we don’t have free downloadable pdf copies of these good books and one should look for free pdf copies from these Authors only if they have explicitly made it free to download and read them.
We have created a collection of best reference books on “Metallurgy” so that one can readily see the list of top books on “Metallurgy” and buy the books either online or offline.
If any more book needs to be added to the list of best books on Metallurgy subject, please let us know.