This set of Advanced Machining Processes Multiple Choice Questions & Answers (MCQs) focuses on “EDM-Applications – 1”.
1. Which of the following shapes can be produced using Electro discharge machining?
a) Complex shapes
b) Simple shapes
c) All of the mentioned
d) None of the mentioned
View Answer
Explanation: Electro discharge machining is used to machine complex shapes to a high degree of accuracy.
2. Which of the following materials can be machined using Electro discharge machining?
a) Heat resistant alloys
b) Super alloys
c) Carbides
d) All of the mentioned
View Answer
Explanation: EDM is used to machine materials such as carbides, heat resistant and super alloys which are difficult-to-machine materials.
3. Which of the following are the applications of Electro discharge machining?
a) Holes
b) Slots
c) Texturing
d) All of the mentioned
View Answer
Explanation: Micromachining of holes, slots, dies, texturing, milling, surface modification and mechanical pulsing are some typical applications of Electro discharge machining.
4. State whether the following statement is true or false regarding the applications of EDM.
“In advanced machining processes, the incorporation of EDM with CIM increased the length of time for unit operation.”
a) True
b) False
View Answer
Explanation: The incorporation of EDM in CIM reduced the length of time per unit operation.
5. Which type of electrode is used for drilling in Electro discharge machining?
a) Flat electrode
b) Cuboidal electrode
c) Tubular electrode
d) Spherical electrode
View Answer
Explanation: Tubular electrode is mostly preferred in Electro discharge machining, for drilling purpose.
6. The dielectric fluid is flushed in thorough which part of the electrode in drilling in EDM?
a) Interior hole
b) Side gaps
c) All of the mentioned
d) None of the mentioned
View Answer
Explanation: EDM drilling uses a tubular electrode which flushes the dielectric thorough the interior holes for removing debris.
7. Which type of holes can be produced through drilling using Electro discharge machining?
a) Irregular
b) Curved
c) Tapered
d) All of the mentioned
View Answer
Explanation: Drilling of work piece using EDM produced holes which can be irregular, curved, tapered as well as inclined holes.
8. What are the values of general feed rates used for drilling in EDM?
a) 0.1 mm/min
b) 0.3 m/min
c) 0.5 mm/min
d) 0.7 mm/min
View Answer
Explanation: Usually a feed rate of 0.10 mm/min is used for drilling the work piece using Electro discharge machining.
9. What are range of diameter values obtained by drilling using EDM?
a) 0.01 to 0.05 mm
b) 0.1 to 0.5 mm
c) 1 to 5 mm
d) 10 to 15 mm
View Answer
Explanation: Diameter values while drilled using Electro discharge machining, ranges from 0.10 to 0.50 mm.
10. What are the values of overcuts left behind after drilling of work piece?
a) 0.01 to 0.05 mm
b) 0.1 to 0.5 mm
c) 1 to 5 mm
d) 10 to 15 mm
View Answer
Explanation: Overcut values from 0.01 to 0.05 mm are obtained after the drilling process in EDM.
11. Electro discharge sawing is an application of EDM which employs __________ as tool material.
a) Steel band
b) Disc
c) Steel band & Disc
d) None of the mentioned
View Answer
Explanation: Electro discharge sawing is an application of EDM which employs either steel band or disc as tool.
12. When compared to the conventional abrasive sawing, how many times faster is the MRR?
a) Twice
b) Thrice
c) Four
d) Five
View Answer
Explanation: Electro discharge sawing cuts the work piece material at the rates which are twice that of conventional abrasive sawing method.
13. How much amount of burr is produce while machined using Electro discharge sawing?
a) 10%
b) 20%
c) 50%
d) No Burr
View Answer
Explanation: The cuts produced in Electro discharge sawing have smaller kerf widths which hav no burrs in it.
14. What are the values of finish obtained by machining work piece thorough Electro discharge sawing?
a) 0.1 to 4 µm
b) 6.3 to 10 µm
c) 12.4 to 23 µm
d) 25.6 to 40 µm
View Answer
Explanation: The finish obtained ranges from 6.3 to 10 µm when machined using Electro discharge sawing.
15. What are the recast layer thickness values obtained in ED sawing?
a) 0.001 to 0.022 mm
b) 0.025 to 0.130 mm
c) 0.236 to 0.352 mm
d) 0.432 to 0.568 mm
View Answer
Explanation: The recast layer thickness values obtained from ED sawing range from 0.025 to 0.13 mm.
Sanfoundry Global Education & Learning Series – Advanced Machining.
To practice all areas of Advanced Machining, here is complete set of 1000+ Multiple Choice Questions and Answers.
If you find a mistake in question / option / answer, kindly take a screenshot and email to [email protected]
- Apply for Mechanical Engineering Internship
- Check Advanced Machining Processes Books
- Practice Mechanical Engineering MCQs
- Check Mechanical Engineering Books